top of page

Support / Bob PetHair SLAM / Replace the Right Sensor Array

Replace the Right Sensor Array

What You Need: (click to shop)

Bob-Pro-Side-Brush.jpg

Flat-Head Screwdriver

Bob-Pro-Side-Brush.jpg

Phillips Head Screwdriver

Bob-Pro-Side-Brush.jpg

Bob-Pro-Side-Brush.jpg

Bob-Pro-Side-Brush.jpg

Bob-Pro-Side-Brush.jpg

Bob's modular design makes it easy to replace old or damaged parts from home. For this repair, you'll need a flat-head screwdriver, a Phillips head screwdriver, and a replacement left sensor array.

Keep all removed screws and parts for later reassembly.

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout_edited_edited.j
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

Before starting, power off Bob by pressing and holding the play button.

1. Remove the battery. Remove the two screws on the battery cover to access the battery. Unplug the battery and set it aside.
2. Remove the front wheel assembly. Using a flathead screwdriver for leverage, pull up on the assembly.
3. Next, remove the side brushes. Pull up to remove them.
4. Then, remove the main brush. Pinch the tabs on the brush gate and lift.
5. Lastly, remove Bob's dustbin.

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

Now, you're ready to open up Bob and access the mainboard.

1. Remove the following eight screws on Bob's underside.
2. Then, remove the eight screws for the bumper attachments.
3. Remove the bumper attachments and set it aside.
4. Flip Bob over to remove the bumper.
5. Disconnect the circuit plug that is connected to the bumper.
6. Then, remove the bumper.

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

Now, it's time to lift Bob's cover.

1. Carefully lift the cover.
2. Disconnect the two circuit plugs connected to the motherboard.
3. Lift the cover and set it on a flat surface.

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

Now, it’s time to replace the right sensor array.

1. Disconnect the circuit plug connected to the mainboard.
2. Then, lift up the sensor bracket.
3. Apply pressure from underneath to pop out the sensor.
4. Lift up the bracket and sensor.
5. Install the new sensor array.
6. Reconnect the circuit plug.
7. The sensor array is now installed.

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

Now it’s time to put Bob back together.

1. Connect the two circuit plugs from the mainboard to Bob's camera.
2. Once connected, close Bob's cover.
3. Reinstall Bob's bumper.
4. Reinstall the bumper attachments.
5. Reinstall the eight screws on Bob's underside.
6. Replace the dustbin, the main brush bracket, and main brush.
7. Replace the side brushes and wheel assembly.
8. Lastly, replace the battery.

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png
05-01-dustbin-slidingout.png

Browse Support Guides

Browse Repair Guides

Shop Parts & Accessories

 

Need a part for your Bob PetHair Appetite? We've got you covered.

​

Visit the bObsweep Shop

Still need help? We’re always eager to chat!

 

For help from a human, contact us at support@bobsweep.com or 1-888-549-8847.

​

Our business hours are Monday – Friday, 9 a.m. – 5 p.m. PT.​

bottom of page